fia0001 's Japan Review

4.50

16 Reviews

10
4
2
0
0
Sort By :

2017-12-11

Since Cosmo's O-rings are thinner than those made by other companies, we were concerned that when using conversion tips made by other companies, the rubber would stick out depending on the barrel, making it impossible to tighten them securely.

When I changed to this O-ring, it did not stick out and I was able to tighten the O-ring beautifully. It's very handy to have one of these!
In my case, when I used Target's titanium tip, the ring no longer protrudes and the compatibility is much better.

I felt the effect on parts that did not fit well and parts that tended to loosen even after tightening.
I never felt that the durability was weak even though it was thin.

Also, when removing the O-ring, a toothpick can be used to remove it cleanly.

17 people found this helpful

2014-06-15

O-ring arrived today. Installation was surprisingly easy. I threw it immediately, and it does not loosen between the barrel and the shaft at all even though I threw it quite a bit. I feel like a fool because of the stress caused by the loosening.... I wish I had bought this product earlier.
The o-ring almost came out when I tightened it, but if I put the o-ring to the end of the thread (open one thread), I was able to install it beautifully without the o-ring coming out (I am using a special shaft for fit flight).

12 people found this helpful

2015-01-06

I have no complaints at all about its performance as an o-ring.
It does not loosen or break. (Especially for fit shafts)

I was looking for a thin o-ring because I didn't like the way it felt and looked on my fingers when I put it on.

As a result, it is by far the thinnest, so my request is perfectly met, but I have to give it -1 for the balance of price/content.
That said, I highly recommend it.

8 people found this helpful

2015-07-05

When I used O-rings from other companies, I had to stop using them because I was worried about them sticking out.
This product does not protrude at all and does not loosen the shaft, so I am very satisfied with it.
Since O-rings themselves are not something that should be replaced so often (for me), I think the price and the amount of contents are also sufficient.

7 people found this helpful

2014-06-30

For those who use fit shafts, which tend to loosen easily, but other o-rings stick out! I would definitely recommend it to those who use fit shafts and tend to loosen easily, but other o-rings stick out!

I use "Monster's barrel" and "fit's slim No. 8", but they are not compatible with each other or something. And when it is loose, the threaded part may be under extra strain, or it may break off frequently. I tried to use a foreign-made o-ring for a while, but the diameter was too thick and it protruded from between the barrel and the shaft, creating an unnecessary gap between the barrel and the shaft.

This product solved that problem.
As expected of Cosmo, the company behind the fit. It doesn't stick out and doesn't loosen even though it is thin. Thanks to this product, the shaft has not broken so far. If I keep using it, I'm sure it will eventually fall off badly and break, but that's just bad luck, lol.

One drawback is the price.
While other foreign-made o-rings and even domestic o-rings cost about 200~300 yen for about 20 pieces, this one costs 400 yen for 12 pieces. It is quite expensive. If the stress of shaft loosening is relieved and the shaft lasts longer, I think the original cost is enough.

For this reason, we deducted one star for cost performance and gave it 4 stars.

7 people found this helpful

2019-01-26

I use it between DMC Sidewinder SUS and RX converter (normal).
It is a great product without any complaints, having all three features: no sticking out, no gap, and no loosening!

5 people found this helpful

2013-01-10

If you have a barrel and shaft that don't match and tend to be loose... I recommend this.
It eliminates the stress of having to close it every time.

4 people found this helpful

2018-05-14

As others have mentioned, this O-ring is thinner than the competitor's product, so it does not stick out of the gap between the barrel and the O-ring.
When I install the other company's product on the shaft I normally use, it definitely sticks out and bothers me when I throw. This one does not, so there is zero stress.
I thought it would break easily, but it doesn't, so it is very useful.
I would have given it 5 stars if the price was a little lower...
Or 1.5x more...

4 people found this helpful

2012-03-08

It prevents the shaft from loosening, thus reducing stress.

4 people found this helpful

2012-12-10

The shaft hardly loosens at all.
I no longer have to stress about re-tightening the shaft every time I throw.
I would like to repeat this when I run out.

4 people found this helpful